precarious Precarious NO. Land of the kaki ...
few days ago I had to install a Red Hat operating system to a customer that uses the modem offered by Tele2:
SpeadTouch 330 silver.
I found a lot of trouble by installing (because of my unfamiliarity with Red Hat), but eventually I did and to be helpful, here is a brief description of what I did.
To install the SpeedTouch 330, you will need:
- speedtouchconf_RedHat.tgz
- ISP Login ID (It is Tele2 on the contract) Wednesday, May 14, 2008
Radiating Tgoughts To A Specific Person
----- -------------------------------------------------- ---------------- 
1 - To begin, create a folder on your desktop and name it "SpeadTouch"
insert inside this manual is that the Artchive: "speedtouchconf_RedHat. tgz " 2 - Open a terminal window and write (commands to type are shown after the symbols "$>"): 1 - To begin, create a folder on your desktop and name it "SpeadTouch" $> cd Desktop / SpeadTouch
$> tar xvzf speedtouchconf_RedHat.tgz
$> Cd speedtouchconf_RedHat
3 - Assicurti that the modem is connected to the computer and check if the ADSL LED is off.
4 - The next command must be run as root. To log in as root type the following command:
$> on
$> "enter the root password"
5 - Proceed with the installation of the modem: $> sh speedtouchconf.sh
6 - When you run this command you will be asked - VPI, VCI, write it like this: 8 35 - your Login ID ISP - your ISP password 7 - appear the inscription: "These Are correct?" you enter Y
(You should see something like that) ************************************
************ * * *
speedtouchconf.sh by Steve Parker * * * * http://speedtouchconf.sourceforge.net/ * * based on project speedtouch.sourceforge.net
* * * *********************************************
*** If you have any problems with this script,
mail me (steve at steve-parker dot org) with the files
/tmp/speedtouch.txt and /var/log/messages for diagnosis.
Is your modem silver in colour? (Revision 400 Speedtouch 330)
Please answer Yes or No
You will need the correct firmware for this modem - currently
available from http://www.ihate.freeserve.co.uk/rev4fw.zip
y
Using speedtouch-1.2-beta3-sgp
Using mgmt.o for microcode
PPP version 2.4.1 okay.
Linux kernel version 2.4.20 okay.
***************************************
* *
* Please select your ISP Settings *
* *
***************************************
Country/ISP VPI VCI
Belgium, ? 8 35
Denmark, Orang 8 35
France, wanado 8 35
France, ? 8 67
Italy, ? 8 35
Netherlands, ? 8 48
UK, BTopenworld 0 38
UK, Any ISP 0 38
US, BellSouth 8 35
Singapore Pacificnet 0 100
Please type your VPI VCI numbers (eg, 0 38 for UK)
8 35
Please enter your ISP Login ID (eg another@hg1.btinternet.com)
***********
Please enter your ISP Password
***********
Settings:
VPI / VCI : 8 / 35
Login : **************
Password : ************** Are these correct? (Y/N)
Y
No further user interaction is required. Configuring SpeedTouch Driver...
Software Configuration - SUCCESS
Building SpeedTouch Driver... Software Build - SUCCESS Installing SpeedTouch Driver...
Software Installation - SUCCESS
*** Configuration finished. Starting the connection ***
The modem lights should start flashing for 20 seconds...
The modem_run command failed (code 250)
modem_run results:
Failed to load microcode - this is not a problem if you have already loaded the microcode. The microcode can only be loaded once per system boot;
We'll assume that the microcode is already loaded, and
not call this an error.
You may encounter problems, though.
Running : pppd call adsl
ppp0: error fetching interface information: Device not found
*********************************
* Don't seem to have connected. *
*********************************
Please check the username and password in /etc/ppp/*-secrets.
Then run /etc/rc.d/init.d/speedtouch
start Current settings: *********** / *********
8 - After this procedure, the modem was installed
9 - To make the connection: $
> etc / init.d / speedtouch start
ADSL modem LED should begin to flash and then remain lit.
When the ADSL LED is lit it means that your modem is connected.
MUST PERFORM THIS PROCEDURE ONLY THE FIRST TIME.
COOLLEGARE FOR THE MODEM ONLY RUN TIME AFTER THE LAST COMMAND
Hope this help.
Subscribe to:
Post Comments (Atom)
0 comments:
Post a Comment